Go Back   Frag Outpost Forums - Coral Propagation and Reef Aquarium Forums > FragOutpost Forums > Coral Propagation

Reply
 
Thread Tools Search this Thread Display Modes
Old 08-21-2005, 06:53 AM   #1
FragOutpost
Administrator
 
FragOutpost's Avatar
 
Join Date: Oct 2004
Location: FL
Posts: 1,333
FragOutpost is on a distinguished road
Default Acropora Propagation

Acropora as well as most all other SPS corals are very easy to propagate. It is as simple as breaking off a branch and attaching it to another piece of rock or rubble with some super glue gel. I use Ross brand super glue gel because it is cheap and readily available but just about any cyanoacrylate based gel super glue will work. Make sure you buy "gel" type super glue. If it doesn't say "gel" on the package it will probably have a very thin consistency and not stick to the frag after you cut it.
Here is the coral I will be fragging -
Attached Images
 
__________________
www.FragOutpost.com



FragOutpost is offline   Reply With Quote
Old 08-21-2005, 06:55 AM   #2
FragOutpost
Administrator
 
FragOutpost's Avatar
 
Join Date: Oct 2004
Location: FL
Posts: 1,333
FragOutpost is on a distinguished road
Default

The tools and materials required for propagating SPS corals include: some pieces of live rock rubble, super glue gel (the thicker the better), and a pair of bone cutters. The bone cutters are optional. A trip to the tool department of your local hardware store should yield a wide variety of tools suitable for the job.
Attached Images
 
__________________
www.FragOutpost.com



FragOutpost is offline   Reply With Quote
Old 08-21-2005, 06:56 AM   #3
FragOutpost
Administrator
 
FragOutpost's Avatar
 
Join Date: Oct 2004
Location: FL
Posts: 1,333
FragOutpost is on a distinguished road
Default

Using your cutting tool of choice, pick up the coral and select a branch to cut. You could just as easily use your hands to snap off a branch, but I find that using a tool leaves for a more precise cut. For the more fragile SPS corals you don't really even need to cut through the branch, instead you may find it easier to hold the branch tight with the cutters and twist or snap the branch off to remove it.
Attached Images
 
__________________
www.FragOutpost.com



FragOutpost is offline   Reply With Quote
Old 08-21-2005, 06:57 AM   #4
FragOutpost
Administrator
 
FragOutpost's Avatar
 
Join Date: Oct 2004
Location: FL
Posts: 1,333
FragOutpost is on a distinguished road
Default

Now that your frag has been cut, apply a generous amount of super glue to the cut part of the frag and to the rubble where you plan to place the frag. Stick the frag to the rubble and hold for about 30 seconds or until the glue has begun to set. Give the glue a few minutes before placing back in your reef aquarium.
Attached Images
 
__________________
www.FragOutpost.com



FragOutpost is offline   Reply With Quote
Old 08-21-2005, 06:57 AM   #5
FragOutpost
Administrator
 
FragOutpost's Avatar
 
Join Date: Oct 2004
Location: FL
Posts: 1,333
FragOutpost is on a distinguished road
Default

Here is the acropora frag glued to the live rock rubble.
Attached Images
  
__________________
www.FragOutpost.com



FragOutpost is offline   Reply With Quote
Old 08-21-2005, 10:41 AM   #6
Peterock
Senior Member
 
Join Date: Aug 2005
Location: denver, co
Posts: 102
Peterock is on a distinguished road
Default

Very nice
Peterock is offline   Reply With Quote
Old 07-03-2006, 09:32 PM   #7
Murfman
125 RR, 49 corner Pony
 
Join Date: Jan 2006
Location: Colorado Springs
Posts: 21
Murfman is on a distinguished road
Default

If you dont have the base of the coral frag, you can take a drill bit or sharp blade and hollow out a hole in the rubble you are using to fit the branch in, makes the superglue work a little better. Just dont go too deep into the rubble or you may "smother" the frag.
Murfman is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 04:22 AM.

 

Powered by vBulletin Version 3.5.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright © 2004 - FragOutpost.com - Coral Frag Trading & Coral Propagation Resources